Search results

Has anyone removed the radio yet and pin tested the harness to figure out what is needed for installing a LOC for aftermarket system? I pulled the stock 8" screw out to get an idea on wire colors but didn't have enough tome to mess with pin each wire out, I have not been able to find and online...

Man these things are so nice! My rig had the factory installed "predator" steps, they were slimy, mounted to the body, and were at a weird Angle to even use as an entry point. Mounted up the CBI overland sliders with th rear kick out, night and day difference. First off weight, you can feel...

my wife loves it, they include a riser for the 14" screen

its just surface rust from where they machined the ends of your castings, mine is doing the same. it will never hurt anything. if you zoom in you can see a few spots, but the pic is showing the cool upgraded Redline Tuning quick lift strut set up Toyota should have installed to being with !

Go with the Bulletpoint RubiGrid set up and you can have a charging set up. It techieonally would have to be wired up, but day to day use you wouldn't have go deal with cords. https://www.bulletpointmountingsolutions.com/products/rubigrid-2024-toyota-tacoma-dash-mount-phone-device-holder

Mounted up the new RubiGrid from Bulletpoint mounting Solutions, they have mounting for the 8" or the 14" screens, and offer a huge array of mounting arms, and attachments for what ever kind of devise you'd like. I choose the simple mag type cell holder and will be adding a mic holder when I...

Installed some of etc SXTH element lower billet recovery hooks in black anodized and they look so much better the next stock! These share the same fitment for the Tacoma. Its a simple 2 bolt swap, take out the stock units, bolts these in ,and have the confidence knowing if you need too, you...

Installed many of these into a wide range of builds, yes you can add some factory switches, but these are way cleaner. You only need to run one small wire into the cabin area, all the rest of your acc wiring will be in the engine bay to the solid state relay block. With 80 amps continual , 2 30...

I know will fit both , glove box organizer , redline tuning quick lift hood struts, sxth front tow hooks

and also pay attention to etc hub bore size, as the new 6th have a smaller bore size, so many wheels will require, or should use a hub centric ring.

dont believe so, but any powder coater could do them

they make lift kits for her also

this is a build that being debuted in April at MOORE Expo, so I can't post full pics till then.

@Diode Dynamics SS5 CrossLink 7-Pod LED Light Bar mounted up on Prinsu Design Studio Pro Roof Rack. https://www.diodedynamics.com/ss5-crosslink-7-pod-led-light-bar-one.html

Diode Dynamics SS5 CrossLink 7-Pod LED Light Bar mounted up on Prinsu Design Studio Pro Roof Rack https://www.diodedynamics.com/ss5-crosslink-7-pod-led-light-bar-one.html

Prinsu pro rack, prinsu ditch light brackets with diode dynamics ss3 https://prinsu.com/category/toyota/4runner/ https://www.diodedynamics.com/?gad_source=1&gbraid=0AAAAADEIEYjrhlse8fLYzmFnzhwIdFjzx&gclid=CjwKCAjwp8--BhBREiwAj7og11lxhfs8owHNaN_ubUY5yoWgtz_J7vKIIvicu0hu0m6EPL1uFRAx0RoCWAYQAvD_BwE

redline tuning gas strut hood props, get rid of stock cheap stock single rod

dirtcom trailswing with frontrunner folding table

been posting lots of detailed pics on separate post, guess I can update here all, kinda forgot about this thread since not much activity. peak suspension

man that thing needs some 37's